LED Lighting Getting Better and Better
Average Rating: ( 0 votes)
This LSI light fixture features the Xicato LED Spot Module, which provides heretofore unavailable light quality from an LED light source: a CRI up to 98 and excellent color consistency. Photo: Lighting Services Inc Click on image to enlarge. I'm j... First, it's much more efficient than incandescent lighting. We refer to lighting efficiency as "efficacy" and measure it in lumens of light output per watt of electricity consumed. Incandescent light bulbs have efficacies of 10-15 lumens per watt, while compact fluorescent lamps (CFLs) come in at 50-70 lumens per watt (lpw) and tubular fluorescent lamps produce as much as 100 lpw. Most LED light sources today deliver 35-60 lpw, though a few exceed 80 lpw. Thus, even though it's often touted as more efficient than fluorescent lighting, most LED lighting today actually has lower efficacy than the best tubular fluorescent lights. Second, LEDs avoid the mercury that used in fluorescent, metal halide, sodium, and mercury-vapor lamps. Mercury is a highly toxic heavy metal; when older fluorescent, metal halide, sodium, or mercury vapor lamps are discarded, there is risk that the mercury in them can escape into the environment--especially if municipal solid waste is incinerated. The Xicato LED Spot Module uses remote phosphor technology and a modular design to provide high-quality light and fast, easy assembly by fixture manufacturers. The LED module needs to be coupled with a heat sink, reflector, and LED driver, all of which are shown in the photo above. Photo: Xicato Click on image to enlarge. Third, well-engineered LED lights last a long time. They can last over 50,000 hours--50 times as long as standard incandescent bulbs, five to ten times as long as compact fluorescent lamps (CFLs), and two to four times as long as linear fluorescent lights. Challenges with LED lighting Creating high-quality white light with LEDs is pretty hard. The first LEDs produced red or green light--these are widely used as indicator lights on stereo equipment and other electronics. To produce white light, manufacturers either combine colored LEDs in carefully balanced mixes (you might remember from high school physics that white is a combination of other colors), or they use phosphor coatings that absorb the colored light and reradiate white light. (Fluorescent lights also rely on phosphor coatings; these absorb the ultraviolet light given off by the electric arc and then "fluoresce" white light.) In the session I moderated at Greenbuild, representatives from two of the leading companies in the LED lighting field talked about the state-of-the-art in LED lighting and the issue of hype vs. reality. The Silicon Valley company Xicato is now producing a modular LED light source that relies on "remote phosphors" to achieve remarkably high-quality light. These Xicato light modules have a "color rendering index" (CRI) as high as 98 (on a scale of 100)--virtually the same as the highest-quality halogen incandescent lamps. They also produce remarkably uniform white light. White LEDs often vary from yellowish to white, and that variability is much lower with the specifications Xicato uses. The company sells the LED modules to fixture manufacturers, which then produce finished light fixtures that use this light source rather than halogen MR-16 lamps. The other company represented in this conference session was Lunera , a manufacturer of a flat-panel LED light fixtures that can be installed in place of standard tubular fluorescent fixtures to provide general illumination. These fixtures are highly controllable, very uniform, and reasonably energy-efficient (though not as energy efficient as tubular fluorescents). Lunera 2200 two-foot by two-foot lay-in ultra-thin LED light fixture for ceiling grid applications to provide area light. Photo: Lunera Click on image to enlarge. One of the most difficult things about choosing LED lighting today is the fact that you can't always trust manufacturer claims. Some manufacturers measure the efficacy of their lamps after they have just been turned on and before they heat up, yielding unrealistically high estimates of efficacy. Some manufacturers also do a poor job at dissipating heat from LEDs. If you don't see aluminum fins on an LED light source, heat may build up shortening the life. I installed one reflector-type screw-in LED lamp several years ago that failed after less than two years--probably after no more than 1,000 hours of operation. This was likely due to heat build-up affecting the LEDs or the LED driver that delivers electricity to the LEDs. The best way to ensure that an LED light source is going to achieve the manufacturer's claims about performance and durability is to look for evidence of independent testing. Some manufacturers have their products tested through the U.S. Department of Energy's CALiPER program and can provide measured test results. Energy Star labels on LED lights also provide evidence that the lights have been independently tested, though there are not yet many products carrying the new Energy Star label for LEDs. Cost also remains an impediment with LED lighting. High-quality LED lights are pretty sophisticated, and you have to pay for that. Cheap LEDs, priced at less than about $20, may not perform well. Like computer chips used in computers, though, costs of LEDs are coming down--and will continue to do so. I fully expect that within ten years--maybe sooner--LED lighting will be cost-competitive with fluorescent lighting and provide better light quality. In addition to this Energy Solutions blog, Alex writes the weekly blog BuildingGreen Product of the Week , which profiles an interesting new green building product each week. You can sign up to receive notices of these blogs by e-mail--enter your e-mail address in the upper right corner of any blog page. Alex is founder of BuildingGreen, Inc. and executive editor of Environmental Building News . To keep up with his latest articles and musings, you can sign up for his Twitter feed .